Es ist ein Slic3r Profil für ABS und den GRRF PRotos Drucker. Wir verwenden die Slic3r Version 0.9.3:
# generated by Slic3r 0.9.3 on Wed Oct 31 17:14:28 2012
acceleration = 0
bed_size = 200,200
bed_temperature = 110
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 70
brim_width = 0
complete_objects = 0
cooling = 1
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M107\n; M104 S0 ; turn off extruder temperature\n; M140 S0 ; turn off plate\nM104 S255 ; turn off extruder temperature\nM140 S110 ; turn off plate\nG28 X0 ; home X axis\nG28 Y0 ; home Y axis\n;G1 Y+100\nM84 ; disable motors\n; M240
external_perimeter_speed = 100%
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 3.9
extrusion_width = 0
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 2.9
fill_angle = 90
fill_density = 0.6
fill_pattern = rectilinear
first_layer_bed_temperature = 110
first_layer_extrusion_width = 0
first_layer_height = 85%
first_layer_speed = 80%
first_layer_temperature = 255
g0 = 0
gcode_arcs = 0
gcode_comments =
gcode_flavor = reprap
infill_acceleration = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_speed = 70
layer_gcode = ; M240
layer_height = 0.4
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
notes =
nozzle_diameter = 0.45
only_retract_when_crossing_perimeters = 0
output_filename_format = [input_filename_base]_PRotos.gcode
perimeter_acceleration = 25
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 40
perimeters = 2
post_process =
print_center = 100,100
randomize_start = 1
retract_before_travel = 4
retract_length = 4
retract_length_toolchange = 3
retract_lift = 0.1
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 200
rotate = 0
scale = 1
skirt_distance = 5
skirt_height = 1
skirts = 3
slowdown_below_layer_time = 15
small_perimeter_speed = 40
solid_fill_pattern = rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_speed = 70
solid_layers = 2
start_gcode = ;PRotos Profile\nG28 ; home all axis\n;M301 P13.82 I0.84 D56.60 ;2PrintBeta Heater\nM301 P26.89 I1.42 D127.33 ;GRRF Heater\n;M301 P50.76 I4.08 D158.02
support_material =
support_material_angle = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_pattern = honeycomb
support_material_spacing = 2.5
support_material_threshold = 45
temperature = 255
threads = 10
top_solid_infill_speed = 50
travel_speed = 150
use_relative_e_distances = 0
z_offset = 0
Unser Profil ist eine angepasste Kopie von Thomas’s Slic3r Profil.
3D Drucker 
Huhu,
das ist ein ABS Profil 🙂
Ihr sollte mal das Bett anpassen, 60 Grad langen
Und Drucktemperatur von 255 Grad für PLA da habt ihr immer Farbe Schwarz .
Was ich empfehlen würde ist noch Z-Lift bei Retract von 0,5 mm, dann rappelt er nicht so über die Plastik.
Aaaaaah! Danke! Habs verwechselt. Ist ein ABS Profil! Ändere gleich den Artikel. Danke für die Anregungen.
… Du meinst also retract_lift = 0.5 statt 0.1?
Jupp
weil 0.1 ist ja nix
und ist das der identische Drucker den ihr auch habt?
Thomas und wir haben beide den PRotos.